Image shows a Basler Ace U acA1920-40gc

CABR273 favorite

Basler Ace U acA1920-40gc

1920 x 1200 Color CMOS GigE Camera

Price: $609.00 each

Not available for purchase outside of North America.

Please sign in to check inventory.

1920 x 1200 images at 40 frames per second
70% quantum efficiency
73 dB dynamic range
45 dB SNR
Compact 42 x 29 x 29 mm housing
Power over Ethernet (PoE) support

The ace series of cameras offer fantastic value. The acA1920-40gc is built on the Sony Pregius IMX249 1/1.2" sensor. It offers 2.3 MP (1920 x 1200) resolution with astounding image quality: high quantum efficiency, wide dynamic range, and extremely low noise.

When this camera is configured to use the sensor's full resolution, it can deliver 40 frames/second ("fps"). However, when configured to use less resolution, the frame rate will increase. As examples, 1920 x 1080 delivers 46 fps, 1920 x 820 delivers 60 fps, and 1920 x 480 delivers 100 fps. (Note maximum frame rate also depends on the output format, exposure time and your network hardware. These frame rates were calculated assuming short exposure and "raw" Bayer RG8 output.)

This camera has relatively large 5.86 µm pixels. This enables greater light sensitivity, greater depth of field, and demands less performance from a lens. If configured to use its full resolution, it has an image circle of 13.27 mm and a 1" lens is needed. To instead use a lower cost 2/3" lens, simply configure the camera for less resolution. All the following resolutions can use a 2/3" (11 mm) lens: 1500 x 1126, 1200 x 1200, 1634 x 920, 1440 x 1200. These resolutions can deliver frame rates of 44, 42, 54 and 42 fps, respectively.

Because the Basler ace GigE camera uses the same 29 x 29 mm footprint that has been standard on analog cameras for many years, replacement of analog cameras is easy. Some existing Camera Link cameras and IEEE 1394a or 1394b cameras with this same footprint can also be easily replaced.

Using a Power over Ethernet (“PoE”) configuration, a single cable may be used to apply camera power and to transfer data between this camera and a PC, keeping cable runs to a minimum. An auxiliary connector is provided for terminating the input and output signal – there is one of each. The input may be configured to trigger image acquisition, reset the frame counter, or reset the software trigger count. The output may be configured to indicate acquisition trigger wait, exposure active, flash window, or timer active. Or the output may be controlled via a PC. The auxiliary connector may be used to power the camera if PoE is not available.

The Basler ace provides a full set of features to address a wide range of applications. Pixel data can be output in 8 or 12 bit depth. You may adjust the camera’s black level, gain, area of interest, input debounce, and trigger delay. It features automatic exposure control, pixel binning, horizontal image mirroring, event reporting, sending of test images, and a programmable lookup table. There are also “chunk” features that include a frame counter, time stamp, trigger input counter, and CRC checksum calculator. Note that not all features may be available when using third-party software.

Because this camera is GigE Vision and GenICam compliant, there are many third party software applications and API’s that are compatible. Basler offers their royalty-free Pylon SDK for 32 and 64 bit Windows and Linux platforms.

Mechanical

Lens Mount: C-Mount

Miscellaneous

Sensor Resolution: 1,920 (h) x 1,200 (v) pixels
Sensor Size: 13.27 mm (1/1.2")
Sensor Model: Sony IMX249LQJ
Chroma: Color Bayer
Shutter Type: Global
Frame Rate (full resolution): 40.0 frames/second
Quantum Efficiency: 70.0 %
Dark Noise: 7.0 e-
Saturation Capacity: 32.8 ke-
Dynamic Range: 74.0 dB
Signal-to-Noise Ratio: 45.0 dB
Test Method: EMVA 1288 for Mono
Data Interface: Ethernet Gig-E Vision
Data Rate: Gigabit Ethernet

Learn about camera specs in our Camera Tech Center.

Loading...


See Resources section below to download drawings.

Resource link Ace Datasheet (PDF) Resource link GigE Tech Center Resource link Pylon Software
Disabled resource link User's Manual (PDF)
Disabled resource link How to trigger a Leimac IDGB strobe controller
Disabled resource link How to trigger a Leimac ILP strobe controller
Disabled resource link Camera Quick Tester Utility
Disabled resource link Drawings
Link to Field of View calculator Select a Lens for Basler Ace U acA1920-40gc Link to Field of View calculator Learn from our Camera Tech Center


Sign In or Register to unlock all links above.

This camera is warranted by the manufacturer to be free from defects in materials and workmanship under normal use for a period of three (3) years from the date of original factory manufacture.

Small quantities of cameras normally stocked by Machine Vision Store may be returned within 30 days, subject to a 20% restocking charge, if original package is unopened and in new condition. Larger quantities are subject to Basler's 40% restocking charge. Open packages may not be returned.

All returns must be pre-authorized by Machine Vision Store and shipped with freight pre-paid. Please contact us to request authorization and instructions. The item's serial number and associated sales order number will be needed.